Dissimilar hardware (M.I.R.)
A backup of the system partition could traditionally only be restored to a computer whose hardware matched the original. With M.I.R. (Machine Independent Restoration), O&O DiskImage restores a backup – including the system partition – to computers with dissimilar hardware, and transfers complete system duplicates to other hardware platforms. M.I.R. replaces or re-integrates the key drivers, especially for mass storage and controllers, so Windows starts despite the changed hardware.
When to enable M.I.R.
Enable M.I.R. whenever the target hardware does not match the original environment or key components changed:
- a restore to a computer with different or newer hardware,
- the duplication or replication of a system to other machines,
- the replacement, removal or addition of mainboard, controllers or mass storage devices,
- the migration between physical systems and virtual machines (P2V and V2P),
- the replacement of faulty or incompatible drivers from the boot medium.
M.I.R. is enabled during the restore or duplication, before the operation completes; afterwards the adaptation runs automatically.
After deploying one Windows installation to several machines, change the computer name and the computer SID to avoid conflicts in workgroups and domains. See System tools.
Restore to dissimilar hardware
M.I.R. is available when the system partition is restored from a backup and when an entire system is duplicated; it does not matter whether the system partition is selected explicitly or an entire disk including the system partition.
- Start the computer from the boot medium. See Boot medium and O&O DiskImage ToGo.
- Select Drive Restore on the start page of the boot medium. O&O DiskImage suggests the location of the most recent backup.
- If the suggested backup is not the right one, browse to the backup file and select Open.
- Enable the checkbox of each drive to restore.
- Select the target drive with its checkbox: an existing drive, or a new one in an unallocated area.
- Open More options and enable Adjust dissimilar hardware afterwards.
- Select Start drive restore and follow the dialogs. After a successful restore, restart the computer when prompted.
The selected target drive is overwritten completely; all data on it is replaced by the contents of the backup.
Limitations of M.I.R.
A restored or duplicated system can still fail to start although M.I.R. was enabled. The cause is usually an incomplete selection:
| Cause | Effect |
|---|---|
| Not the entire disk was selected as the target, but a single partition, a volume or a free area. | System and boot information that exists only on the full disk is missing. |
| Delete layout was not selected when the target layout was created. | Partitions can be created at different offsets, so Windows no longer finds its boot areas. |
| Only individual source partitions were selected instead of the entire disk. | Boot areas such as the EFI partition, recovery partitions or the Windows boot manager are missing. |
| The bootable drive is attached to a controller that is not initialized at boot time, for example an internal drive on a USB controller. | Windows does not detect the drive in time during the boot. |
To keep a restored system or duplicate bootable, always back up and restore or duplicate the entire system disk, not individual partitions.
Manual adjustment
If the system does not start as expected after the restore, or devices are not detected, adjust the hardware manually: restore or duplicate as usual, then open Tools > Change Computer Properties and supplement the missing adjustments. The adaptation of M.I.R. consists of three actions that can be enabled or disabled during a restore to dissimilar hardware:
| Action | Meaning |
|---|---|
| Replace Hardware Abstraction Layer (HAL) | The HAL encapsulates architecture-specific functions such as interrupt controllers, multiprocessor communication and I/O interfaces, and is tightly bound to the hardware. After a change of mainboard or CPU it must be adapted so that Windows runs stably. |
| Adopt currently loaded device-control drivers | Integrates or replaces the device drivers, so Windows can access the new hardware after the restore. |
| Trigger operating system setup on next restart | Instructs Windows to run an internal setup routine on the next start, which registers new hardware and completes missing system information. |
Next steps
- Restore the entire system
- Clone drives – duplicating a system to other hardware.